2012 Washington wildfires

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
2012 Washington wildfires
File:2012-Sept-19 NASA Washington smoke.jpg
Satellite image of fires on September 19
Statistics[1]
Total fires 1,342
Total area 259,526 acres (1,050 km2)

The 2012 Washington wildfires were are series of 1,342 wildfires that burned 259,526 acres (1,050 km2) over the course of 2012.[1] The fires primarily occurred in the Okanogan and Wenatchee National Forests during September and October 2012.[citation needed] A severe lightning storm on September 8 caused hundreds of fires across the east side of Cascade Range. Smoke caused hazardous air quality conditions in the cities of Ellensburg and Wenatchee,[2] and was noticeable in Seattle. The cost of fighting the largest four fires was estimated to be $67.5 million.[3]

Taylor Bridge Fire

The first major wildfire in Washington during the 2012 season started on August 13 east of Cle Elum between Interstate 90 and U.S. Route 97 in Kittitas County. The fire was fully contained on August 28 after burning Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value). acres and destroying 61 homes. The cause of the fire is under investigation, but is suspected to be construction work.[3]

September 8 lighting-strike fires

  • Okanogan Complex[4]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Three fires in the lower Methow River valley, on either side of State Route 153 in Okanogan County.
  • Wenatchee Complex[5]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. The largest fires were south of U.S. Route 2 near the city of Wenatchee mainly in Chelan County. Other fires in the complex were in the upper Entiat and Wenatchee River drainages.
    • Byrd Fire – Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).
    • Canyon Fire – Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Located less than a mile west of the city of Wenatchee in Number 1 and Number 2 canyons.
    • Cashmere Fire – Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Located south of Icicle Creek extending into the Alpine Lakes Wilderness.
    • Peavine Canyon Fire – Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. The Peavine Canyon Fire grew to become contiguous with the Table Mountain Fire to the south.
    • Poison Canyon Fire – Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).
  • Table Mountain Fire[6]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Located east of U.S. Route 97 near Blewett Pass in Kittitas County, the Table Mountain Fire threatened homes and historic structures near Liberty, Washington. The fire grew to become contiguous with the Peavine Canyon Fire to the north.
  • Yakima Complex[7]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Approximately 75 small fires in Kittitas and Yakima counties. The Wild Rose Fire was the largest and is located north of U.S. Route 12 and east of Rimrock Lake.
  • Cascade Creek Fire[8]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Located on the south and west slopes of Mount Adams in the Gifford Pinchot National Forest, including part of the Mount Adams Wilderness. Skamania and Yakima counties.

Other fires

  • Goat Fire[9]Lua error in Module:Convert at line 1851: attempt to index local 'en_value' (a nil value).. Human-caused fire began on September 16, located south of State Route 153 and west of U.S. Route 97 in Okanogan County.

References

  1. 1.0 1.1 Lua error in package.lua at line 80: module 'strict' not found.
  2. Lua error in package.lua at line 80: module 'strict' not found.
  3. 3.0 3.1 Lua error in package.lua at line 80: module 'strict' not found.
  4. Lua error in package.lua at line 80: module 'strict' not found.
  5. Lua error in package.lua at line 80: module 'strict' not found.
  6. Lua error in package.lua at line 80: module 'strict' not found.
  7. Lua error in package.lua at line 80: module 'strict' not found.
  8. Lua error in package.lua at line 80: module 'strict' not found.
  9. Lua error in package.lua at line 80: module 'strict' not found.

External links