Agatti Aerodrome
| Agatti Aerodrome അകറ്റി വിമാനത്താവളം |
|||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Aerial view of Agatti Aerodrome
|
|||||||||||
IATA: AGX – ICAO: VOAT
 AGX
|
|||||||||||
| Summary | |||||||||||
| Airport type | Public | ||||||||||
| Operator | Airports Authority of India | ||||||||||
| Serves | Lakshadweep, India | ||||||||||
| Location | Agatti Island | ||||||||||
| Elevation AMSL | 14 ft / 4 m | ||||||||||
| Coordinates | Lua error in package.lua at line 80: module 'strict' not found. | ||||||||||
| Runways | |||||||||||
|
|||||||||||
Agatti Aerodrome (IATA: AGX, ICAO: VOAT) is located on the southern end of Agatti Island, in the union territory of Lakshadweep in India. It is the sole airstrip in the archipelago, which lies off the west coast of India.
Contents
History
The airstrip was constructed during 1987−88 for operation of Dornier 228 type of aircraft and was inaugurated on 16 April 1988. Initially, the terminal was housed in a small temporary structure. Construction of Terminal Building, Air Traffic Control Tower and related structures commenced in 2006. However, the construction of the Terminal Building was stopped midway due to the proposed extension of Runway & Basic strip.[1] Air India Regional began services with ATR-42 aircraft on 24 September 2010 connecting Agatti with Kochi.[2] The resurfacing of the runway was completed in November 2010.[1]
Structure
Agatti airport is spread over 18.56 hectares (45.9 acres). It has one asphalt runway, oriented 04/22, 1204 metres long and 30 metres wide, while its terminal building can handle 50 passengers during peak hours. Navigational aids include a DME and NDB. It is operated by the Airports Authority of India (AAI).[3]
Expansion
The Airports Authority of India (AAI) received environmental clearance to extend the runway by constructing a 1,500-feet-long bridge on stilts over the sea. The extension is to be built at a cost of Rs 300 crore and will allow aircraft like the ATR-72 to be operated without any payload restrictions. The AAI originally planned to construct a bridge between Agatti and the neighbouring uninhabited Kalpati Island to make the runway long enough to handle an Airbus A-320 or Boeing 737.[4] However, this plan was rejected on environmental grounds as the bridge would have gone through a turtle colony and Kalpati island would need to be levelled to accommodate the extended runway.[5]
As per the revised master plan,[1] the following works will be undertaken
- The existing runway will be extended by 336 metres in the south-west direction over the lagoon towards Kalpati Island without interconnecting the two islands.
- Construction of new Terminal building, ATC tower cum Technical block & Fire Station in the north-west direction by constructing a platform supported by R.C.C pillars on the lagoon.
- A Fully air conditioned Terminal building covering 2250 square metres to cater for 150 passengers at a time (75 arriving and 75 departing).
- The existing Control Tower cum fire station and existing Terminal building that falls inside of the proposed basic strip will be demolished.
- A new 118×62 metre apron suitable for parking two ATR-72 aircraft with power-in and power-out configuration will be constructed on a platform supported by RCC pillars in the lagoon.
- Runway End Safety Area (RESA) measuring 60×90 metres and a Blast Pad/Overrun area measuring 60×30 metres.
- 73 metre long taxiway from the Runway to the Apron.
- Parking area for 75 cars about 2,000 square metres (22,000 sq ft).
- Proposed DVOR and NDB navigational aids will be placed on Kalpati island.
Airlines and destinations
| Airlines | Destinations |
|---|---|
| Air India Regional | Bengaluru,[6] Kochi |
References
- ↑ 1.0 1.1 1.2 Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Agatti Aerodrome at Airports Authority of India
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
