Indicated airspeed
Indicated airspeed (IAS) is the airspeed read directly from the airspeed indicator on an aircraft, driven by the pitot-static system.[1] It uses the difference between total pressure and static pressure, provided by that system, to either mechanically or electronically measure dynamic pressure. The dynamic pressure includes terms for both density and airspeed. Since the airspeed indicator cannot know density, it is by design calibrated to assume the sea level standard atmospheric density when calculating airspeed. Not least since the actual density will vary considerably from this assumed value as the aircraft changes altitude, IAS varies considerably from true airspeed (TAS), the relative velocity between the aircraft and the surrounding air mass. Calibrated airspeed (CAS) is the IAS corrected for instrument and position error.[1]
An aircraft's indicated airspeed in knots is typically abbreviated KIAS for "Knots-Indicated Air Speed" (vs. KCAS for calibrated airspeed and KTAS for true airspeed).
The IAS is an important value for the pilot because it is the indicated speeds which are specified in the aircraft flight manual for such important performance values as the stall speed. These speeds, in true airspeed terms, vary considerably depending upon density altitude. However, at typical civilian operating speeds, the aircraft's aerodynamic structure responds to dynamic pressure alone, and the aircraft will perform the same when at the same dynamic pressure. Since it is this same dynamic pressure that drives the airspeed indicator, an aircraft will always, for example, stall at the published indicated airspeed (for the current configuration) regardless of density altitude or true airspeed.[2]
Furthermore the IAS is specified in some regulations, and by air traffic control when directing pilots, since the airspeed indicator displays that speed (by definition) and it is the pilot's primary airspeed reference when operating below transonic or supersonic speeds.
Contents
IAS vs CAS
The IAS is not the actual speed through the air even when the aircraft is at sea level under International Standard Atmosphere conditions (15°C, 1013 hPa, 0% humidity). The IAS needs to be corrected for known instrument and position errors to show true airspeed under those specific atmospheric conditions, and this is the CAS (Calibrated Airspeed). Despite this the pilot's primary airspeed reference, the ASI, shows IAS (by definition). The relationship between CAS and IAS is known and documented for each aircraft type and model.
IAS and V speeds
The aircraft's pilot manual usually gives critical V speeds as IAS, those speeds indicated by the airspeed indicator. This is because the aircraft behaves similarly at the same IAS no matter what the TAS is: E.g. A pilot landing at a hot and high airfield will use the same IAS to fly the aircraft at the correct approach and landing speeds as he would when landing at a cold sea level airfield even though the TAS must differ considerably between the two landings.
Whereas IAS can be reliably used for monitoring critical speeds well below the speed of sound this is not so at higher speeds. An example: Because (1) the compressibility of air changes considerably approaching the speed of sound, and (2) the speed of sound varies considerably with temperature and therefore altitude; the maximum speed at which an aircraft structure is safe, the never exceed speed (abbreviated VNE), is specified at several differing altitudes in faster aircraft's operating manuals, as shown in the sample table below.
| Diving below | mph IAS |
| 30,000 ft | 370 |
| 25,000 ft | 410 |
| 20,000 ft | 450 |
| 15,000 ft | 490 |
| 10,000 ft | 540 |
Ref: Pilot's Notes for Tempest V Sabre IIA Engine - Air Ministry A.P.2458C-PN
For navigation, it is necessary to convert IAS to TAS and/or ground speed (GS) using the following method:
- correct IAS to calibrated airspeed (CAS) using an aircraft-specific correction table;
- correct CAS to true airspeed (TAS) by using Outside Air Temperature (OAT), Pressure-altitude and CAS on an E6B flight computer or equivalent functionality on most GPSs;
- convert TAS to ground speed (GS) by allowing for the effect of wind.
With the advent of Doppler radar navigation and, more recently, GPS receivers, with other advanced navigation equipment that allows pilots to read ground speed directly, the TAS calculation in-flight is becoming unnecessary for the purposes of navigation estimations.
TAS is the primary method to determine aircraft's cruise performance in manufacturer's specs, speed comparisons and pilot reports.
Other airspeeds
From IAS, the following speeds can also be calculated:
- convert CAS to equivalent airspeed (EAS) by allowing for compressibility effects (not necessary at slow speed or low altitude); EAS is used by aircraft engineers and some very high-altitude flying aircraft such as the U-2 and the SR-71;
- convert EAS to true airspeed (TAS) by allowing for differences in density altitude.
On large jet aircraft the IAS is by far the most important speed indicator. Most aircraft speed limitations are based off IAS, as IAS closely reflects dynamic pressure. TAS is usually displayed as well, but purely for advisory information and generally not in a prominent location.
Modern jet airliners also include ground speed (GS) and Machmeter. Ground speed shows the actual speed that the aircraft uses compared to the ground. This is usually connected to a GPS or similar system. Ground speed is just a pilot aid to estimate if the flight is on time, behind or ahead of schedule. It is not used for takeoff and landing purposes, since the imperative speed for a flying aircraft always is the speed against the wind.
The Machmeter is, on subsonic aircraft, a warning indicator. Subsonic aircraft must not fly faster than a specific percentage of the speed of sound (at present conditions, which varies by altitude and air density). Usually passenger airliners do not fly faster than around 85% of speed of sound, or Mach 0.85. Supersonic aircraft, like the Concorde and military fighters, use the Machmeter as the main speed instrument with the exception of take-offs and landings.
Some aircraft also have a taxi speed indicator for use on the ground. Since the IAS often starts at around 40-50 knots (on jet airliners), pilots may need extra help while taxiing the aircraft on the ground. Its range is around 0 to 50 knots.
See also
Notes
- ↑ 1.0 1.1 Clancy, L.J. (1975), Aerodynamics, Section 3.9, Pitman Publishing Limited, London. ISBN 0-273-01120-0
- ↑ Kermode, A.C.,Mechanics of Flight, 8th Edition – page 64. Longman Group Limited, London ISBN 0-582-23740-8
References
- Gracey, William (1980), "Measurement of Aircraft Speed and Altitude" (11 MB), NASA Reference Publication 1046.
