A label (as distinct from signage) is a piece of paper, polymer, cloth, metal, or other material affixed to a container or product, on which is written or printed information about the product. Information printed directly on a container or article can also be considered labeling.
Labels have many uses including providing information on a product's origin, use, shelf-life and disposal, some or all of which may be governed by legislation such as that for food in the UK or USA. Methods of production and attachment to packaging are many and various and may also be subject to internationally recognised standards.
- 1 Uses
- 2 Stock types
- 3 Attachment
- 4 Usability
- 5 Environmental considerations
- 6 Other aspects
- 7 See also
- 8 References
- 9 Further reading
- 10 External links
Labels may be used for any combination of identification, information, warning, instructions for use, environmental advice or advertising. They may be stickers, permanent or temporary labels or printed packaging.
Permanent product identification by a label is commonplace; labels need to remain secure throughout the life of the product. For example, a VIN plate on an automobile must be resistant to heat, oils and tampering; similarly, a food label must endure until the food has been used.
Removable product labels need to bond until they are removed. For example, a label on a new refrigerator has installation, usage and environmental information: the label needs to be able to be removed cleanly and easily from the unit once installed.
Packaging may have labeling attached to or integral with the package. These may carry pricing, barcodes, UPC identification, usage guidance, addresses, advertising, recipes, and so on. They also may be used to help resist or indicate tampering or pilferage.
In industrial or military environments, asset labeling is used to clearly identify assets for maintenance and operational purposes. Such labels are frequently made of engraved Traffolyte or a similar material. They are usually tamper-evident, permanent or frangible and usually contain a barcode for electronic identification using readers. For example, the US Military uses a UID system for its assets.
Garments normally carry separate care/treatment labels which, in some regions, are subject to legislation. Textile labels may be woven into the garment or attached, and may be heat resistant (so survivable in hot-air dryers and when pressed), colorfast (so does not bleed onto the garment), washable, leather or PVC/Plastic. Printed labels are an alternative to woven labels.
Textiles containing pesticides as an ingredient may also require government approval and compulsory labeling. In the USA, for example, labels have to state the pesticide registration number, statement of ingredients, storage and disposal information, and the following statement: "It is a violation of Federal Law to use this product in a manner inconsistent with its labeling”. A label including a company name or identification number and a material content list may also be required.
Mailing labels identify the addressee, the sender and any other information which may be useful in transit. Many software packages such as word processor and contact manager programs produce standardized mailing labels from a data set that comply with postal standards. These labels may also include routing barcodes and special handling requirements to expedite delivery.
- Piggyback labels are made from combining two layers of adhesive substrate. The bottom layer forms the backing for the top. The label can be applied to any object as normal, the top layer can be a removable label that can be applied elsewhere, which may change the message or marking on the remaining label underneath. Often used on Express mail envelopes. Other applications include price change labels where when being scanned at the till, the till assistant can peel back the price-reduction label and scan the original barcode enabling stock flow management. Also, as the retained label is adhesive free it prevents customers from re-applying the cheaper priced labels to premium products.
- Smart labels have RFID chips embedded under the label stock.
- Blockout labels are not see-through at all, concealing what lies underneath with a strong gray adhesive.
- Radioactive labels The use of radioactive isotopes of chemical elements, such as carbon-14, to allow the in vivo tracking of chemical compounds.
- Laser or printer labels are generally die cut on 8.5" x 11" (US letter) or A4 sized sheets, and come in many different shapes, sizes, formats and materials. Laser label material is a nonporous stock made to withstand the intense heat of laser printers and copiers. A drawback of laser labels is that the entire sheet needs to be printed before any labels are used; once labels have been removed the sheet cannot be put through the printer again without damaging the printing mechanism. Inkjet label material is a porous stock made to accept ink and dye from an inkjet printer. One of the more modern inkjet label material stocks is waterproof printable inkjet material commonly used for soap or shower gel containers.
- Security labels are used for anti-counterfeiting, brand protection, tamper-evident seals, anti-pilferage seals, etc. These combine a number of overt and covert features to make reproduction difficult. The use of security printing, holography, embossing, barcodes, RFID chips, custom printing, weak (or weakened) backings, etc. is common. They are used for authentication, theft reduction, and protection against counterfeit and are commonly used on ID cards, credit cards, packaging, and products from CDs to electronics to clothing.
- Antimicrobial labels. With the growth in hospital acquired infections such as MRSA and E-Coli the use of antimicrobial labels in infection sensitive areas of hospitals are helping in combating these types of microbes.
- Fold-out labels, also known as booklet, multi-page or extended labels, or lablets (combined label + leaflet). Where the pack is not large enough for a single label to carry all the required information, fold-out labels are often preferred to separate leaflets, which can easily be lost. These labels are frequently seen on agricultural chemicals and consumer pharmaceuticals.
- Barcode labels A large proportion of labels produced today carry barcodes, either for product identification, for traceability in items such as freight packages, and on items requiring brand authentication and protection. There are many different formats of barcodes found on labels, but one of the most commonly distributed formats is the International Article Number (EAN). This is the code used to identify retail products worldwide, and is found on almost all consumer level packaging labels.
Label "stock" is the carrier which is commonly coated on one side with adhesive and printed on the other, and can be:
- Paper - a variety of papers and paperboards can be used as labels
- Nonwoven fabric - for extra durability
- Latex – a lithographic stock with some added latex allows the label to be much more flexible and form around certain curved objects more easily than standard paper;
- Plastics such as acetate, vinyl, and PET film allow a variety of features, such as greater strength, stiffness, transparency, resistance to tearing, etc. They typically require special equipment and printing methods (ultra-violet curing is common) as they do not normally print well with conventional ink. A bumper sticker is usually a vinyl label with a very strong, durable adhesive and lightfast inks. Embossing tape is "printed" by pressing raised elements similar to printing type onto it, which produces raised glyphs that look white due to discoloration of the plastic. A type known as 'Destructible Vinyl' is commonly used for asset labels. It combines a very thin frangible face stock with a very strong high tack adhesive, thus making the label impossible to remove without damaging it. Engraved multi-layer Traffolyte labels are frequently used in industrial situations due to their durability;
- Foil – has the shiny properties of a metal foil;
- Thermal – direct thermal label stock will change color (usually black) when heated. A heating element in the shape of letters or images can be used to create an image on the label. Custom labels can be easily be made on location in this way. A disadvantage is durability, because another heat source can ruin or obscure the image, or it may fade completely over time;
- Thermal Transfer for applications that cannot use Thermal (Thermal Direct) label material because of heat source proximity or short label life, a more widely used material is Thermal Transfer Label printer. This material has the advantage of a much longer readable life and does not fade with time or heat. Most major manufacturers of Thermal Printers can be used for either Thermal Transfer (TT) or Thermal (DT) labels. A thermal transfer ribbon will be required to print the labels. The cost of the ribbons + TT labels is similar to that of the DT labels on their own;
- Thermal Transfer Ribbon Types:
- Wax is the most popular with some smudge resistance, and is suitable for matte and semi-gloss paper labels;
- Wax / Resin is smudge resistant, suitable for semi-gloss paper and some synthetic labels;
- Resin is scratch and chemical resistant, suitable for coated synthetic labels;
- None – labels can be printed directly on adhesive without using a substrate. Labels made in this manner are extremely fragile, however, and have been rendered virtually obsolete by other printing methods such as silk screen;
The stock type will affect the types of ink that will print well on them. Corona treating or flame treating some plastics makes them more receptive to inks and adhesives by reducing surface tension.
Labels can be attached by:
- Heat activated adhesives: for example, "in-mold labeling" can be part of blow molding containers and employs heat activated adhesives. Hot melt adhesives are also used.
- Pressure-sensitive adhesives (also called PSA or self-stick) are applied with light pressure without activation or heat. PSA labels often have release liners which protect the adhesive and assist label handling.
- Rivets used to attach information plates to industrial equipment.
- Shrink wrap for printed shrinkable labels placed over packages and then heated to shrink them.
- Sewing for clothing, tents, mattresses, industrial sacks, etc.
- Wet glue such as starch, dextrin, PVA or water moistenable gummed adhesive.
- Yarn, twine or plastic tie, usually referred to as a swing tag.
- Static cling, where "stickers" have a static charge enabling them to attach without adhesive to smooth surfaces such as glass.
PSA adhesive types
Pressure-sensitive label adhesives are commonly made from water based acrylic adhesives, with a smaller volume made using solvent based adhesives and hotmelt adhesives. The most common adhesive types are:
- Permanent – Typically not designed to be removed without tearing the stock, damaging the surface, or using solvents. The adhesion strength and speed can also be varied. For example, full adhesion can be nearly instant, or the label can be almost removable for a short period with full adhesion developing in minutes or hours (known as respositionable adhesives).
- Peelable – Adhesion is fairly strong and will not fall off in normal circumstances, but the label can be removed relatively easily without tearing the base stock or leaving adhesive behind on the old surface. The adhesive is usually strong enough to be applied again elsewhere. This type is frequently known as 'removable'. There are many different types of removable adhesives, some are almost permanent, some are almost 'ultra peelable'.
- Ultra-peelable – Designed principally for use on book covers and glass, when removed these adhesives labels do not leave any residue whatsoever. Adhesion is weak and only suitable for light duty applications. Normally these labels have very little adhesion to anything once they've been removed.
- Freezer or Frost fix – Most permanent and peelable adhesives have a service temperature limit of -10 degrees Celsius, whereas freezer (otherwise known as frost fix) adhesives have a service temperature -40 degrees Celsius and are suitable for deep freeze use.
- High Tack – A type of permanent adhesive that exhibits a high initial grab to the application surfaces, and is commonly used at higher coat weights to enable labels to adhere strongly to difficult, rough or dirty surfaces.
Labels may be supplied separately or on a roll or sheet.
Many labels are pre-printed by the manufacturer. Others have printing applied manually or automatically at the time of application. Specialized high speed label printer applicators may be used to apply labels to packages; these and other methods may subject to recognized standards.
Some labels have protective overcoats, laminates, or tape to cover them after the final print is applied. This is sometimes before application and sometimes after.
Labels are often difficult to peel and apply. A label dispenser can speed up this task.
Aspects such as legibility, literacy and interpretation come into play for users of labels, and label writers therefore need some degree of professional writing skill. Depending upon country or region, international standards may be applied. Where literacy may be an issue, pictograms may feature alongside text, such as those advanced by CropLife International in their Responsible Use manual. Labels or printed packaging may include Braille to aid users with visual impairment.
Criticism of label readability is not uncommon; for example, Canadian researchers found that medicine labels did not consistently follow legibility guidelines. In some countries and industries, for example the UK (food) and EU (medicines) label guidelines are not legally binding (the latter using phrases such as "The type size should be as large as possible to aid readers...") and thus are unenforceable. On the other hand, countries may stipulate legal minima for readability, such as the USA's FDA on nutritional information and Australia/New Zealand's code for food labels and packs.
Labels may have an impact on the environment during manufacture, use, and post-use. Choice of backings, coatings, adhesives, and liners can be strong factors. Environmental regulations and guidelines can come from many sources. Users of labels on packaging may consider some of the sustainable packaging guidelines.
Based on the solid waste hierarchy, the quantity and size of labels should be minimized without reducing necessary functionality. Material content of a label should comply with applicable regulations. Life cycle assessments of the item being labeled and of the label itself are useful to identify and improve possible environmental effects. For example, reuse or recycling are sometimes aided by a label being removable from a surface.
If a label remains on an item during recycling, a label should be chosen which does not hinder the recyclability of the item. For example, when labeled corrugated boxes are recycled, wet strength paper labels do not hinder box recycling: the PSA adhesive stays with the backing and is easily removed. Paper backings without wet strength may release their adhesives, potentially contaminating recycling efforts.
An eco-label is used on consumer products (including foods) to identify products that may be less damaging to the environment and/or humans than other related products, such as sustainable seafood encouraged by Friend of the Sea.
Ink and base stock color choices commonly conform to the Pantone Matching System (PMS) colors. The Pantone system is very dominant in the label printing industry. Additionally specialty inks such as metallic, UV ink, magnetic ink, and more are available. Ink is usually transparent however it can be made opaque. It has been known for certain companies to patent "their own" color. Digital labels use process colors to replicate Pantone solid colors.
Collecting labels is a worldwide phenomenon, from labels used on matchboxes and foodstuffs to printed packages. Collectors are attracted to labels both for their impact on artistic design and the history of retailing.
- "UK Food Labelling & Packaging". Retrieved 5 Mar 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "FDA Food Label Requirements in a Nutshell". Retrieved 12 June 2015.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Paula, K; Ashraf, A (January 4, 2013). "Asset Labels, Asset Sticker, Property ID, Property Labels: Asset Label Generator". Asset Labels Australia.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Clothes Captioning: Complying with the Care Labeling Rule". (November 2001). Bureau of Consumer Protection, Federal Trade Commission (United States)
- "Textile Industry Affairs: Writing a care label". Retrieved 5 Mar 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Threading Your Way Through the Labeling Requirements Under the Textile and Wool Acts". (May 2005). Bureau of Consumer Protection, Federal Trade Commission (United States)
- "Examples of printer label formats" (PDF). Iidsolutions.co.uk. Retrieved 2013-10-28.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- ASTM D5375 Standard Test Methods for Liner removal at High Speeds from Pressure-Sensitive Label Stock.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles> ASTM
- ASTM D6252 Standard Test Method for Peel Adhesion of Pressure Sensitive Label Stocks at 90 deg Angle.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles> ASTM
- Gold, Karen (13 June 1992). If all else fails, read the instructions. New Scientist.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- ASTM D7298-06 Standard Test Method for Measurement of Comparative Legibility by Means of Polarizing Filter Instrumentation.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles> ASTM
- "The Responsible and Effective Use of Crop Protection Products". Retrieved 14 December 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Small font, all capitals makes prescription labels too hard to read". Retrieved 14 July 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Food Standards Agency - Clear food labelling - Guidance" (PDF). Retrieved 14 July 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Eurpopean Commission: Guideline of the readability of the labelling and package leaflet of medicinal products for human use" (PDF). Retrieved 14 July 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "FDA - Labeling and Nutrition". Retrieved 14 July 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Food Standards Australia New Zealand" (PDF). Retrieved 14 July 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Kovach, A; Brown, S (July 1, 2008). "Label recycling: a materials issue". Packaging Digest.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Katz, S (July 2008). "Waste Recycling". Label and Narrow Web.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Jensen, Timothy (April 1999). "Packaging Tapes:To Recycle of Not". Adhesives and Sealants Council. Archived from the original on 2007-11-09. Retrieved 2007-11-06.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Lua error in Module:Citation/CS1/Identifiers at line 47: attempt to index field 'wikibase' (a nil value).
- "Sustainable Seafood Products Certification". Retrieved 17 May 2014.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Opie, Robert (1987). The Art of the Label. Simon & Schuster. p. 140. ISBN 0671654411.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Yam, K. L., "Encyclopedia of Packaging Technology", John Wiley & Sons, 2009, ISBN 978-0-470-08704-6
- Holkham, T., Label Writing and Planning – A guide to good customer communication, Chapman & Hall 1995, ISBN 0-7514-0361-X
|Wikimedia Commons has media related to Labels.|
- Boston Public Library, USA. Produce Crate Labels, ca. pre-1950s