Motorcycle trailer
A motorcycle trailer is either a trailer used to carry motorcycles or one to be pulled by a motorcycle in order to carry additional gear.
Contents
For carrying motorcycles
Motorcycle carrying trailers may be open or enclosed. They may be wide, for two machines side-by-side, or narrow, for just a single machine. The main features that distinguish them from other flatbed or enclosed trailers are track(s) to keep the wheels from sliding side to side and sufficient tiedown points to keep the motorcycle(s) from tipping. They may also tilt, or include ramp(s) to facilitate the loading and unloading of motorcycles. Trailer manufacturers often offer trailers specifically designed for carrying motorcycles.
Enclosed trailers, as seen in the photos, have the advantage of protecting motorcycles within from the weather and from prying eyes, and of being able to lock the motorcycles up securely. However, they are heavier than open trailers and create more wind resistance, decreasing the fuel efficiency of the towing vehicle. An enclosed motorcycle-specific trailer can be built low enough so as not to increase resistance due to wind, thus substantially maintaining efficiency.
Collapsible or folding motorcycle trailers are available to overcome storage problems that might prevent use of a non-collapsible trailer, some such trailers are sufficiently compact to allow the user to carry the trailer in the trunk of a car when not in use.
Types
The basic motorcycle trailer design consists of a fixed platform mounted above an axle, which requires the motorcycle be loaded by physically lifting it or rolling it up a ramp onto the platform, potentially a difficult problem when dealing with a heavy touring machine or one that has been disabled. Since the latter half of the 20th century a number of different trailer styles have been devised to make loading motorcycles on them easier. Broadly, such designs include:
- Tilt-bed, wherein the platform teeters on the axle, bringing the tail of the trailer to ground level. The motorcycle is pushed or ridden onto the trailer bed, which in some designs automatically tilts back to the horizontal and locks in place when the load moves forward of the bed pivot point. Such designs still require the machine be pushed up an inclined plane.
- Drop-bed, wherein the platform is lowered to the ground in a substantially horizontally fashion and the motorcycle has only to be rolled or ridden over the lip of the platform and secured to it, whereupon the entire platform and load are raised and secured for towing. Such designs only require the machine be raised by the thickness of the platform, which is typically less than 10 cm (4 in). Numerous mechanical designs have been devised by trailer fabricators to achieve this goal.
For pulling by motorcycles
Trailers towed behind motorcycles are distinguished by their relatively small size, especially narrow wheelbase. They are also often styled to match the look of the motorcycle they are intended to be towed behind. This styling can include the overall shape, fender shape, lights, chrome, etc.
The Guinness World Record for a motorcycle and trailer is 139.5 mph, set in 2002 by Motor Cycle News (UK) towing a Squire D21 trailer behind a Kawasaki ZZ-R1100.
In the United Kingdom there are some legal restrictions on towing trailers.[1]
- Only motorcycles with engine displacement over 125 cm3 (7.6 cu in) may tow.
- The motorcycle must be marked with its kerbside weight.
- The trailer must not be wider than 1 m (3 ft 3 in).
- The distance between the rear axle of the motorcycle and the rear-most part of the trailer must not exceed 2.5 metres (8 ft 2 in).
- The laden weight of the trailer must not exceed 150 kg (331 lb) or two-thirds of the kerbside weight of the motorcycle, whichever is lighter.
- The trailer must be clearly and indelibly marked with its unladen weight.
- The UK speed limit is 60 mph on motorways and dual carriageways and 50 mph on all other roads unless a lesser limit is in force.
- The trailer must display the same registration plate as the towing vehicle.
- Trailers must have two red sidelights, two red stop lights, a number plate light, two triangular red reflectors and amber indicators (which flash between 60 and 120 times per minute) at the rear.
- All trailers built after September 30, 1990 also require white front reflectors.
Safety tips for towing include:
- Motorcycle manufacturers do not recommend that trailers be towed by their motorcycles because of the increased safety hazards. All towing is done at the operator's own risk.
- A ball hitch, where used, should be well greased at all times to facilitate smooth cornering.
- While towing a trailer, one must remember to ride closer to the center of the lane, taking the width of trailer into account. Be careful of the "oil strip" in the center of the lane at intersections, especially when it begins to rain after an extended dry spell. Also, watch for uneven road surfaces and road edges that can unbalance the trailer.[2]
- Keep enough of the weight forward of the axle to maintain a positive hitch load when loading the trailer.[3]
- The Pav 40/41/100
The Pav trailers were manufactured in the Czech Republic, originally by "AVIA n.p". and later by "KOVOZAVODY SEMILY" by Jawa Moto. Earliest examples were made in the mid- to late-1950s, which pre-date the PAV 40. The PAV 40 debuted in approximately 1958 or 1959. The PAV 41 eventually replaced the PAV 40 and was produced into the 1970s. Pav trailers feature a single 4-inch (102 mm) wheel and are rated to 80 km/h (50 mph). They were made to be attached to Jawa motorcycles, although they make excellent accessories for Vespa, Lambretta, Cezeta, Heinkel, Fuji, Zundapp, Cushman, or any other vintage motorcycle, scooter or microcar (like Isetta or Messerschmitt). Having just one wheel, these trailers are attached to the towing vehicle by a hitch that has only two degrees of freedom — pitch and yaw.
Hitching a trailer to a motorcycle
<templatestyles src="Module:Hatnote/styles.css"></templatestyles>
In order to tow a trailer behind a motorcycle, one of the following coupling combinations or mechanisms is needed: a ball and socket, swivel adapter, or pivot ball hitch and coupler.
Ball and socket
Most trailers are towed by joining a ball and a coupler (socket).[4] The coupler is attached to the trailer, and the ball hitch is attached to the tow vehicle. The coupler slides over the ball hitch. Then, pressure is applied to a clamp, usually with a toggle or lever, which secures the
ball in the coupler. To ensure that the appropriate amount of pressure is applied, the coupler is equipped with a locknut that allows the operator to adjust the tension. When properly attached, the coupler will have limited movement, swiveling mainly right and left as well as tilting slightly.[5]
Swivel adapter (swivel coupler - swivel hitch)
The swivel adapter, more commonly referred to as a swivel coupler or swivel hitch,[6] functions by connecting one end to the trailer tongue and the other end directly to the hitch on the tow vehicle or to a coupler. This mechanism is engineered to rotate on the vertical axis so as to eliminate the possibility of coupler binding. As a result, the motorcyclist is able to lean into a turn as far as necessary at high speeds while keeping the trailer upright.
Anti-binding motorcycle trailer hitch assembly (pivot ball hitch)
The pivot ball hitch is an anti-binding motorcycle trailer hitch assembly composed of a base and a trailer ball. The base is secured to a standard ball mount on the motorcycle. The trailer is attached to a socket coupler. A space between the ball shank and the assembly mount allow the ball to move left and right in a vertical plane. Thus, the ball remains in a generally upright position when the motorcycle leans left or right into a turn because the base of the pivot ball hitch is able to move in the opposite direction of the motorcycle without causing the coupler to bind.[7]
Coupler binding
Making a turn on a single-track vehicle such as a two-wheeled motorcycle requires the driver to lean the bike. The amount of the lean is dependent upon the speed. Faster speeds require more leaning than slower speeds do.[8] When making a turn with a trailer attached, the mechanism that joins the trailer to the motorcycle must allow for an appreciable lean in order for a trailer to stay upright. Without the ability to freely rotate on a vertical axis, the coupler will bind and the trailer will jack-knife or flip.[9]
As explained above in "Ball and socket", the movement in the coupler and ball combination is limited to mostly horizontal movement and tilting slightly. Therefore, this type of coupling is best suited for three-wheeled motorcycles and four-wheeled vehicles. In contrast, as pivot ball hitches and swivel adapters do allow the appreciable lean necessary to keep all the trailer wheels on the ground while turning, these devices are the better option for towing trailers behind a two-wheeled motorcycle.[10][4]
References
|
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ 4.0 4.1 Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
| Chassis |
 |
||||||||
|---|---|---|---|---|---|---|---|---|---|
| Engine |
|
||||||||
| Transmission |
|
||||||||
| Accessories | |||||||||
| Other | |||||||||
.JPG){kind=link}
