North American BT-9

From Infogalactic: the planetary knowledge core
(Redirected from North American NJ-1)
Jump to: navigation, search
BT-9/BT-14/NJ
North American NJ-1 in flight 1938.jpeg
A U.S. Navy NJ-1 in flight, 1938
Role Trainer
Manufacturer North American Aviation
First flight April 1936
Primary users United States Army Air Corps
United States Navy
Number built +260
Unit cost
$20,000 USD
Developed from North American NA-16
Developed into North American BC-1

The North American BT-9 was the United States Army Air Corps (USAAC) designation for a low-wing single piston engine monoplane primary trainer aircraft that served before and during World War II. It was a contemporary of the Kaydet biplane trainer and was used by pilots in Basic Flying Training following their completion of Primary in the Kaydet. The NJ-1, which was similar to the one off BT-10 was used by the United States Navy.

Design and development

The BT-9, designated NA-19 by the manufacturer, evolved from the North American NA-16, which first flew in April 1935. The BT-9 design first flew in April 1936.[1]

The wing and tail control surfaces were fabric-covered, as well as the sides of the fuselage from just behind the firewall to the tail. The remainder of the aircraft was metal-covered and featured fixed (non-retractable) landing gear. The Army Air Corps purchased a total of 199 BT-9s, BT-9As and BT-9Bs. Many foreign countries also used variants of this aircraft under North American's NA-16 designation.

The first BT-9C s/n 37-383 was built with a 600 hp Pratt & Whitney R-1340-41, but was otherwise similar to the normal BT-9Cs. It was delivered as the Y1BT-10, and later redesignated BT-10.

The BT-9D was a one off prototype that tested out a number of ideas that went into production as the BT-14 (NA-58), which the similar North American NA-64 Yale represented a major aerodynamic improvement over the NA-16 series, with a longer all-metal fuselage replacing the fabric covered fuselage of the earlier NA-16s. The BT-14 featured a Pratt & Whitney R-985 engine versus the Wright R-975 used on the BT-9. As well as metal skin replacing the fabric on the fuselage, the fin was moved aft slightly, lengthening the rear fuselage while the engine was moved forward to maintain the center of gravity. The rudder was also changed from the rounded shape used previously to one with a roughly triangular shape, with the broadest part being at the bottom, and the canopy was redesigned. The new fuselage would provide the basis for the entire AT-6 family, when fitted with the larger Pratt & Whitney R-1340 engine, a new wing with retractable undercarriage and minor changes for a gunners position.

The BT-9 suffered from stall/spin problems and a variety of fixes were tried. The USAAC temporarily settled on using slats on the later versions of the BT-9. However these did not work well, and the BT-14s longer fuselage and swept forward outer wing panels, unlike the straight trailing edges of the BT-9 helped somewhat.

Operational history

BT-9 production in 1936.

The NA-26, an improved model with retractable landing gear which became the prototype for AT-6 Texan advanced trainer, was developed from the NA-16 design.

Variants

Source: Warbirds[2]
NA-16
Prototype aircraft, one built.
NA-18
Pre-production aircraft, one built.
North American BT-9
Unarmed two-seat primary trainer for the USAAC, 42 built.
BT-9A at Langley
North American BT-9A
Armed with two 0.30 in (7.62 mm) machine guns, 40 built.
North American BT-9B
Improved unarmed version, 117 built.
North American BT-9C
Similar to the BT-9B, but with some equipment changes, 97 built.
North American BT-9D
One prototype only, which lead to the development of the BT-14.
North American Y1BT-10 & BT-10
One prototype from BT-9C batch re-engined with a 600 hp R-1340-41.
North American NJ-1
Two-seat primary trainer aircraft for the USN, powered by a 600 hp (447 kW) Pratt & Whitney R-1340 radial piston engine, 40 delivered.
BT-14
North American YBT-14
Redesignated BT-9D as prototype for BT-14.
North American BT-14
Advanced version with lengthened metal fuselage and T-6 outer wing panels, powered by a 450 hp (336 kW) Pratt & Whitney R-985-25 radial piston engine, USAAC, 251 delivered.
North American BT-14A
27 BT-14s were converted to take the 400 hp (298 kW) Pratt & Whitney R-985-11 radial piston engine.

Operators

 United States

Survivors/Aircraft on display

BT-9
BT-14[3]

Specifications (BT-9)

General characteristics

  • Crew: two, instructor and student
  • Length: 28 ft (8.5 m)
  • Wingspan: 42 ft (12.8 m)
  • Height: 13 ft 7 in (4.1 m)
  • Loaded weight: 4,470 lb (2,030 kg)
  • Powerplant: 1 × Wright R-975-53, 400 hp (300 kW)

Performance

See also

Related development
Aircraft of comparable role, configuration and era
Related lists

References

Notes

  1. "BT-9 Yale." Boeing History. Retrieved: 5 February 2011.
  2. Hanson, Dave. "Warbirds: BT-9." warbirdalley.com. Retrieved: 5 February 2011.
  3. "BT-14s." AeroWeb. Retrieved: 24 December 2011.

Bibliography

  • Davis, Larry. T-6 Texan in Action (Aircraft Number 94). Carrollton, Texas: Squadron/Signal Publications, Inc., 1989. ISBN 0-89747-224-1.
  • Donald, David. American Warplanes of World War II. London: Aerospace Publishing, 1995. ISBN 1-874023-72-7.
  • Fletcher, David C. and Doug MacPhail. Harvard! The North American Trainers in Canada. San Josef,BC/Dundee,Ont: DCF Flying Books, 1990. ISBN 0-9693825-0-2.
  • Hagedorn, Dan. North American NA-16/AT-6/SNJ (WarbirdTech Volume 11). North Branch, Minnesota: Specialty Press, 1997. ISBN 0-933424-76-0.
  • Morgan, Len. Famous Aircraft Series: The AT-6 Harvard. New York: Arco Publishing Co., Inc., 1965.