Run-off-road collision

From Infogalactic: the planetary knowledge core
Jump to: navigation, search

A run-off-road collision (or roadway departure) is a US term for a type of single-vehicle collision that occurs when a vehicle leaves the roadway. Contributing factors often include loss of control or mis-judging a curve, or attempting to avoid colliding with another road user or an animal.

If the vehicle strikes a fixed object (an object that will move very little when struck, such as a tree, bridge structure or utility pole) or rolls over, the crash is likely to result in injuries or fatalities. 2005 statistics from the US show that run off road crashes resulted in 31% of fatal crashes, but were only 16% of all crashes.[1] Run-off-road collisions where the vehicle is sliding or spinning and runs broadside into a fixed obstacle are particularly dangerous, since the vehicle doors and sides provide less protection to occupants than the front of the car.

Clear zones

An important concept in understanding run-off-road crashes is the clear zone. This is the roadside area that is free from obstacles and dangerous slopes. Early research at the General Motors Proving Grounds found that 80% of their test drivers stopped or regained vehicle control within 30 feet (9 m) of the edge of the travel lane. As a result, civil engineers began to try to provide thirty feet of clear, flat ground next to rural highways. The result was fewer crashes. Current guidance adjusts the desired clear zone width for curvature, roadside slope, speed and volume. More width is recommended on the outsides of curves, where the ground slopes down away from the road, and on high speed, high volume roads.[2]

Prevention and mitigation

There are several ways to reduce consequences of run-off-road collisions. They fall into three main categories: preventing run-off-road incidents, minimizing the likelihood of a crash or roll-over if the vehicle travels off the shoulder, and reducing the severity of those that do occur.[3]

Roadway cross section improvements

Roadway cross section improvements include high friction overlays, improving curve banking, and widening shoulders or travel lanes. The intention is to help the driver to keep the car on the roadway. They are usually expensive unless included in a highway reconstruction project.

A relatively inexpensive countermeasure is the placement of a Safety Edge — a 30° compacted taper on the edge of the pavement. This helps any driver that runs off the edge of the roadway to maintain control while trying to steer back onto the pavement. A vertical edge dropoff often results in overcorrection, leading to a head-on collision, rollover, or a run-off-road collision on the far side of the road. Pavement edge dropoffs are problematic on roads where the hard shoulder is narrow or nonexistent. The safety edge adds about 1% to the pavement costs while building or resurfacing a road.[4]

Hazard removal or modification

If possible, hazards should be removed, or modified to be less dangerous. Examples include tree removal, using forgiving road infrastructure or extending cross culverts out of the clear zone. Regarding forgiving road infrastructure: standards exist in different countries to crash test road infrastructure and to qualify them as being passive safe or forgiving. In US there is MASH and in Europe, there is EN12767. Removing obstacles should be the first choice. If that is not possible, make them forgiving. As a last option, isolate the obstacle with a guard rail.

Guard rail is used to reduce the severity of run-off-road crashes by interposing a barrier that is more forgiving to vehicle occupants. It is important to note that guard rail is itself a hazard and should only be used where it shields traffic from a hazard that is more dangerous than it is. It may not reduce the number of run-off-road crashes, since it is longer and closer to the road than the hazard behind it. Properly designed and installed, it will reduce the severity of crashes that do occur. One study found that installing guard rail above an embankment would only reduce run-off-road crashes by only 7%. However, injury and fatal crashes were reduced by 45%.[5]

Delineation

Where hazard removal and guardrail reduce the severity of run-off-road crashes, delineation aims to reduce the frequency of crashes by helping drivers stay on the road. It includes pavement markings, object markers, curve warning signs, delineators, and arrows and chevrons on curves. It is used where other improvements would be too costly or ineffective, as an interim method until other improvements can be installed, and to help drivers avoid collisions with guarderail. Signing improvements will generally reduce crashes by about 30%.[5] Because of its low cost, delineation is often the measure of choice on lower volume roads.

Some of these measures can also reduce the frequency and severity of head-on collisions. Median barriers are a form of guard rail that turn head-on crashes into fixed object crashes. Curve delineation and cross-section improvements can reduce loss-of-control incidents.

Cost-effectiveness

Since most roadway improvements are funded by taxes or user fees, it is important that safety improvements pay for themselves. On low speed, low volume local roads, expensive improvements are likely to produce less in savings than they cost, and thus divert scarce resources from locations where they could be better used. On high speed, high volume freeways, high quality clear zones are worth the cost.[citation needed]

See also

References

  1. National Highway Traffic Safety Administration, Traffic Safety Facts 2005, 2007, P. 54. http://www-nrd.nhtsa.dot.gov/Pubs/TSF2006.PDF
  2. New York Department of Transportation Highway Design Manual, https://www.dot.ny.gov/divisions/engineering/design/dqab/hdm/chapter-10
  3. Lua error in package.lua at line 80: module 'strict' not found.
  4. Lua error in package.lua at line 80: module 'strict' not found.
  5. 5.0 5.1 Desktop Reference for Crash Reduction Factors, Federal Highways Administration Report No. FHWA-SA-07-015, retrieved from http://ite.org/safety/issuebriefs/Desktop%20Reference%20Complete.pdf, October 31, 2008.