Stamping (also known as pressing) is the process of placing flat sheet metal in either blank or coil form into a stamping press where a tool and die surface forms the metal into a net shape. Stamping includes a variety of sheet-metal forming manufacturing processes, such as punching using a machine press or stamping press, blanking, embossing, bending, flanging, and coining. This could be a single stage operation where every stroke of the press produces the desired form on the sheet metal part, or could occur through a series of stages. The process is usually carried out on sheet metal, but can also be used on other materials, such as polystyrene.
Stamping is usually done on cold metal sheet. See Forging for hot metal forming operations.
Stamped parts were used for mass-produced bicycles in the 1890s. Stamping replaced die forging and machining, resulting in greatly reduced cost. Although not as strong as die forged parts, they were of good enough quality.
Stamped bicycle parts were being imported into the United States from Germany in 1890. U.S. companies then started to have stamping machines custom built by U.S. machine tool makers. Through research and development Western Wheel was able to stamp most bicycle parts.
Several automobile manufacturers adopted stamped parts before Ford Motor Company. Henry Ford resisted the recommendations of his engineers to use stamped parts, but when the company could not satisfy the demand with die forged parts, Ford was forced to use stampings.
- Bending - the material is deformed or bent along a straight line.
- Flanging - the material is bent along a curved line.
- Embossing - the material is stretched into a shallow depression. Used primarily for adding decorative patterns. See also Repoussé and chasing.
- Blanking - a piece is cut out of a sheet of the material, usually to make a blank for further processing.
- Coining - a pattern is compressed or squeezed into the material. Traditionally used to make coins.
- Drawing - the surface area of a blank is stretched into an alternate shape via controlled material flow. See also deep drawing.
- Stretching - the surface area of a blank is increased by tension, with no inward movement of the blank edge. Often used to make smooth auto body parts.
- Ironing - the material is squeezed and reduced in thickness along a vertical wall. Used for beverage cans and ammunition cartridge cases.
- Reducing/Necking - used to gradually reduce the diameter of the open end of a vessel or tube.
- Curling - deforming material into a tubular profile. Door hinges are a common example.
- Hemming - folding an edge over onto itself to add thickness. The edges of automobile doors are usually hemmed.
Piercing and cutting can also be performed in stamping presses. Progressive stamping is a combination of the above methods done with a set of dies in a row through which a strip of the material passes one step at a time.
The tribology process generates friction which requires the use of a lubricant to protect the tool and die surface from scratching or galling. The lubricant also protects the sheet metal and finished part from the same surface abrasion as well as facilitate elastic material flow preventing rips, tears or wrinkles. There are a variety of lubricants available for this task. They include plant and mineral oil based, animal fat or lard based, graphite based, soap and acrylic based dry films. The newest technology in the industry is polymer based synthetic lubricants also known as oil-free lubricants or non-oil lubricants. The term "Water-Based" lubricant refers to the larger category that also includes more traditional oil and fat based compounds.
Sheet metal forming simulation is a technology that calculates the process of sheet metal stamping, predicting common defects such as splits, wrinkles, springback and material thinning. Also known as forming simulation, the technology is a specific application of non-linear finite element analysis. The technology has many benefits in the manufacturing industry, especially the automotive industry, where lead time to market, cost and lean manufacturing are critical to the success of a company.
Recent research by the Aberdeen research company (October 2006) found that the most effective manufacturers spend more time simulating upfront[clarification needed] and reap the rewards towards the end of their projects.
Stamping simulation is used when a sheet metal part designer or toolmaker desires to assess the likelihood of successfully manufacturing a sheet metal part, without the expense of making a physical tool. Stamping simulation allows any sheet metal part forming process to be simulated in the virtual environment of a PC for a fraction of the expense of a physical tryout.
Results from a stamping simulation allow sheet metal part designers to assess alternative designs very quickly to optimize their part for low cost manufacture.
Industry Specific Processes
Metal stamping can be applied to a variety of materials based on their unique metalworking qualities for a number of applications across a wide range of industries. Metal Stamping may require the forming and processing of base common metals to rare alloys for their application specific advantages. Some industries require the electrical or thermal conductivity of beryllium copper in areas such as aerospace, electrical, and the defense industry or the high strength application of steel and its many alloys for the automotive industry. Industries Metal Stamping is used for:
- Lawn Care & Equipment
- Lock Hardware
- Power Storage
- Power Tools
- Small Engine
- Circle grid analysis
- Forming limit diagram
- Four-slide machine, a combination stamping, bending, and punching machine
- Progressive stamping
- Shearing (manufacturing)
- Kalpakjian, Serope; Schmid, Steven (2001). Manufacturing Engineering and Technology (International edition. 4th ed.). Prentice Hall. ISBN 0-13-017440-8.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Hounshell, David A. (1984), From the American System to Mass Production, 1800-1932: The Development of Manufacturing Technology in the United States, Baltimore, Maryland: Johns Hopkins University Press, ISBN 978-0-8018-2975-8, LCCN 83016269<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Hounshell 1984, pp. 208–12
- Hounshell 1984
- Hedrick, Art (December 15, 2009). "Sheet Metal Stamping 101, part V". Fabricators and Manufacturers Association.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Sheet Metal Stamping".<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "The Simulation-driven Design Benchmark Report: Getting It Right the First Time". Aberdeen Group. 2006-10-31. Retrieved 2011-11-07.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- "Metal Stamping Industries". Trans-Matic Manufacturing, Inc. Retrieved 2014-04-18.<templatestyles src="Module:Citation/CS1/styles.css"></templatestyles>
- Don Hixon, 1984, December, "Alternative Lubricant Offers Advantages for Stamping", Precision Metal, page 13
- William C. Jeffery, 1985, November, "Non-Oil Drawing Compounds Make Dollars and Sense", Metal Stamping, pages 16–17
- Phillip Hood, 1986, Spring, "Environmental Compliance - A Lawn and Garden Manufacturers' Approach to Stamping Lubricants and Environmental Change", Stamping Quarterly, Pages 24–25
- Pioneer Press, April 27, 1989, Marilyn Claessens, "At 75, IRMCO still a pioneer - Lubricants go down the drain by design", Evanston, IL, page 33
- Bradley Jeffery, 1991, August, "Environmental Solutions for Metal Stamping", MAN, pages 31–32
- Robin P. Bergstrom, 1991, November, "Stamping Made Clean(er)", Production Magazine, pages 54–55
- 1991, February, "Lubricants and Environment Mix", Manufacturing Engineering, pages 52–59
- Brian S. Cook, 1992, January 6, "Appropriate Technology", Industry week, pages 51–52, 58.
- James R. Rozynek, 1995, Winter, "Case Study: Converting to Water-Based Metal Stamping Lubricants", Stamping Quarterly, pages 31–33
- Philip Ward, 1996, July/August, "Water-Based Stamping Lubricant Washes Away Oil-Based Lube Problems", Forming & Fabricating, pages 52–56
- Matt Bailey, UK, 1997, May, "Non-Oil Lubricants Offer Solvent Solution", Sheet Metal Industries, pages 14–15
- Chris Wren, UK, 1999, June, "One Out - Oil Out" Sheet Metal Industries, pages 21–22
- Brad Jeffery, 2003, April, "The Bottom Line - Getting your N-Values Worth", Modern Metals, page 76
- Brad F. Kuvin, 2007, February, "Forming Advanced High Strength Steel Leaves No-Room for Error", MetalForming, pages 32–35
- Brad F. Kuvin, 2007, May, "Dana's Giant Lube Leap of Faith", MetalForming, pages 32–33
- Hyunok Kim PhD, 2008, March "Evaluation of Deep Drawing Performance of Stamping Lubricants with Dual Phase (DP) 590 GA", Part II in III part series, The Center for Precision forming (CPF), The Ohio State University, pages 1–5
- Brad F Kuvin, January, 2009, "Deep-Draw Automation returns remarkable results", MetalForming, pages 14–15