Cath lab
Lua error in package.lua at line 80: module 'strict' not found.
A catheterization laboratory or cath lab is an examination room in a hospital or clinic with diagnostic imaging equipment used to visualize the arteries of the heart and the chambers of the heart and treat any stenosis or abnormality found.
Equipment
Most catheterization laboratories are "single plane" facilities, those that have a single X-ray generator source and an image intensifier. Older cath labs used cine film to record the information obtained, but since 2000, most new facilities are digital. The latest digital cath labs are biplane (have two X-ray sources) and digital, flat panel labs.
A typical 'Cath Lab' will consist of:
- Patient Couch
- A floor or ceiling mounted Image intensifier
- Set of viewing monitors
- Realtime ECG/Blood pressure/Oxygen Saturation measurements with software to record and measure these when needed
- Injector Pump used for imaging the Left Ventricle or Aorta
- X-ray software for the recording and playback of the Fluoroscopy runs acquired during the procedure
- Diagnostic Catheters
- Guide catheters
- Guidewires
- Angioplasty balloons
- Stents (drug eluting and bare metal)
- Sheaths
- Closure devices
- General nursing supplies
- Defibrillator
- Drugs
- Wireless Headset Systems for Cath Labs[1]
- Recovery bays
- Reporting station
- Scrub area
Staff
Cardiac catheterisation laboratories (or Cath Lab) in the UK are usually staffed by a multidisciplinary team. This includes a Medical Practitioner (normally either a Consultant Cardiologist or Radiologist), a Cardiac Physiologist, a Nurse and a Radiographer.
Medical Practitioner The Consultant Cardiologist is responsible for gaining arterial access, inserting a sheath into either the radial or femoral artery, passing a wire and catheter into the coronary artery and selectively injecting contrast media into the coronary arteries. They then interpret the images taken to ascertain where the narrowed or blocked artery has the problem. They use a variety of techniques and imaging tools to work the size of things such as balloons and stents.
Cardiac Physiologist Cardiac Physiologists usually set up what is known as a transducer to monitor pressure in the arteries. They also have a live view of the patients ECG so they can tell whether or not there is a problem being caused by the insertion of the catheter into the heart to the electrical pathways. The physiologist will also set up a temporary pacemaker if the procedure is an angioplasty or a PCI. Finally, they also set up defibrillators on to the patient for emergency use if needed.
Procedures
<templatestyles src="Module:Hatnote/styles.css"></templatestyles>
"Cardiac catheterization" is a general term for a group of procedures that are performed using this method, such as coronary angiography, as well as left ventricle angiography. Once the catheter is in place, it can be used to perform a number of procedures including angioplasty, PCI (percutaneous coronary intervention) angiography, balloon septostomy, and an Electrophysiology study or Catheter ablation.
A list of procedures carried out in a Cath Lab includes:
- Coronary Angiography or Coronary catheterization
- Coronary Angioplasty or Percutaneous coronary intervention / PCI
- Closure of some congenital heart defect
- Treatment of stenotic heart valves
- Permanent and temporary pacemaker implantations
- Electrophysiological studies such as AV node ablation
- Rotablation of heavily Calcified vessels
- Left and right Sided pressure studies
- Radiofrequency Catheter Ablation
Projections
Any combination of the following views are used in visualising the Coronary Arteries:
- PA (Postero-antero) 90 degree
- RAO (Right Anterior Oblique) 30 degree
- RAO CRANIAL 30 degree RAO & 30 degree CRA
- PA CRANIAL
- LAO CRANIAL
- LAO (Left Anterior Oblique)
- LAO CAUDAL (or 'spider' view)
- PA CAUDAL
- RAO CAUDAL
As a general rule, cranial views are best used to demonstrate the Left Anterior Descending Artery or 'LAD', and caudal views are best used to demonstrate the Circumflex Artery or LCX.
See also
References
- ↑ Lua error in package.lua at line 80: module 'strict' not found.
