Holden HZ

From Infogalactic: the planetary knowledge core
Jump to: navigation, search
Holden HZ
File:1979-80 HZ Kingswood Palais White==.JPG
Holden Kingswood (HZ) SL sedan
Overview
Manufacturer Holden (General Motors)
Production October 1977–April 1980
Assembly Acacia Ridge, Queensland, Australia
Elizabeth, South Australia, Australia
Dandenong, Victoria, Australia
Pagewood, New South Wales, Australia
Trentham, New Zealand
Body and chassis
Class Full-size
Body style 4-door sedan
5-door station wagon
2-door coupe utility
2-door panel van
2-door cab chassis
Related Statesman HZ
Powertrain
Engine I6
  • 3.3 L 88 kW (118 hp) Red

V8

  • 4.2 L 120 kW (161 hp) Red
  • 5.0 L 161 kW (216 hp) Red
Transmission 3-speed manual
4-speed manual
3-speed automatic
Chronology
Predecessor Holden HX
Successor Holden WB
Holden VB Commodore

Holden HZ is a full-sized automobile which was produced in Australia between October 1977 and 1980 by Holden in a variety of equipment levels and in several different body styles. It was also assembled in New Zealand.

Characteristics

The Holden HZ received minor updates to the exterior over the HX series, and saw the introduction of what Holden termed "Radial Tuned Suspension" (RTS) across all models. RTS made significant changes to the suspension of the car, greatly improving the handling finesse, while at the same time not compromising ride quality.[1] Modern Motor magazine described the HZ as "a great handler spoiled by the car" in a comparison against the BMW 528i, contrasted as "a great car spoiled by the handling".[2] In this series, the base specification Belmont was deleted and the new Kingswood SL became the base luxury level for sedans and wagons, with a lower specification Kingswood sedan and wagon only offered as a delete option on the Kingswood SL. During the course of the HZ series, equipment levels were upgraded in 1978 effectively to match improvements in the opposition Ford Falcon range, but the life of the full W size Holden looked set to end following Holden's release of the VB Commodore in November 1978. After 1980, W sized Holden passenger cars were cancelled—replaced by the downsized Commodore. The Kingswood luxury level lived on until 1985 on the WB Holden utility but the end of HZ saw the end of the Holden Premier alongside both the GTS and Sandman which were both deleted prior to the end of the HZ series.

Model range

The Holden HZ was offered in four sedan and three station wagon models, marketed as follows:

  • Holden Kingswood Sedan[3]
  • Holden Kingswood Wagon[3]
  • Holden Kingswood SL Sedan[4]
  • Holden Kingswood SL Wagon[4]
  • Holden Premier Sedan[5]
  • Holden Premier Wagon[5]
  • Holden GTS[6]

It was also available in two coupe utility, two panel van and one cab chassis model, marketed as follows:

  • Holden Ute[7]
  • Holden Kingswood Ute[7]
  • Holden Van[7]
  • Holden Kingswood Van[7]
  • Holden One Tonner[7] (cab chassis)

There were two special vehicle packages also available based upon commercial vehicles:

  • Holden Sandman Ute[8] and Holden Sandman Van [8] - option code XX7 (passenger tyres) or XU3 (load rated tyres).
  • Ambulance - option code BO6, available on cab chassis and Holden panel van.

Sandman Ute and Van

The final HZ Sandman, featured a choice of V8 engines only, along with a four-headlight grille and under bumper front spoiler. According to a GMH Price List dated 25 January 1979, a basic HZ Holden panel van was priced at A$6,076, with the Sandman option package an additional A$1,700. The further optional components also included 5.0-litre V8 engine and a limited slip differential. If a buyer selected every Sandman extra, the price would be more than 150% of the cost of the basic HZ model. By the end of 1979, the Sandman had largely lost its place in the contemporary Australian youth culture - order figures were down and many of the vehicles were now being sold with the stripes and tailgate logos deleted. The Sandman ute was phased out of production prior to the van, the last of which was manufactured around October 1979.

See also

References

  1. Wright (1998), p. 2240–241
  2. Lua error in package.lua at line 80: module 'strict' not found.
  3. 3.0 3.1 Holden HZ Technical Specifications Retrieved from www.uniquecarsandparts.com.au on 23 January 2011
  4. 4.0 4.1 Holden HZ Kingswood SL sales brochure, H665, September 1977
  5. 5.0 5.1 Holden HZ Premier sales brochure, H664, September 1977
  6. Holden HZ GTS sales brochure, H666, September 1977
  7. 7.0 7.1 7.2 7.3 7.4 Holden HZ Utes, Vans & One Tonner sales brochure, K247, October 1977
  8. 8.0 8.1 Holden HZ Sandman sales brochure, K249, October 1977