Balloon loop

Balloon loop at Linnéplatsen at the tramway in Göteborg, Sweden.

Double sided island platform on a balloon loop - Olympic Park, Sydney, Australia
P1 & P4 departures
P2 & P3 arrivals

Maules Creek & Boggabri Coal Terminal East balloon loops

A balloon loop or turning loop allows a rail vehicle or train to reverse direction without having to shunt or even stop. Balloon loops can be useful for passenger trains and unit freight trains such as coal trains.

Balloon loops are common on tram or streetcar systems. Many streetcar and tram systems use single-ended vehicles that have doors on only one side and must be turned at each end of the route, or else haul trailer cars with no driver's cabin in the rear car.

History

Balloon loops were first introduced on metro and tram lines. They did not appear on freight railways in large numbers until the 1960s when the modernising British Rail introduced merry-go-round (MGR) coal trains that operated from mines to power stations and back again without shunting.

Tramways

Balloon loops enable higher line capacity (faster turnaround of a larger number of trams) and also allow the use of single-ended trams which have several advantages, including lower cost and more seating when doors are on one side only. However, double-ended trams also benefit from the capacity advantage of balloon loops, for example on the former Sydney tram system where loops were used from 1880 until the system's closure in 1961. Initially the Sydney system was operated by single-ended steam trams and then, from the 1890s, by double-ended electric trams. Lines were looped in the Sydney CBD and the other busiest areas of operation, such as the La Perouse, New South Wales and other eastern suburbs lines, as they provided greater turn-around capacity on this very busy system. The Sydney system was possibly the first major example of a looped tramway system. European systems were extensively converted to looped operation in the early twentieth century and most of them changed to single-ended trams. Looped operation with single-ended trams was also used on many North American streetcar systems.

Examples

Passenger

South Ferry balloon loop

On a balloon loop: the station is on the balloon loop, and the platform may be curved or straight.

Australia

Penfield - now closed and removed
Outer Harbor - now closed and removed
Olympic Park, Sydney, Australia: platforms 1 and 4 are for boarding, 2 and 3 for alighting.
Beech Forrest, Victoria, Australia: single platform station on Victorian narrow gauge railway.

Canada

Toronto streetcar loops

United States

Lower level (suburban) layout of the Grand Central Terminal, showing a balloon loop

Upper level (mainline) layout of the Grand Central Terminal, showing a balloon loop

City Hall subway station on the IRT Lexington Avenue Line in New York City is now closed, although the loop track continues to be used to turn trains. These trains discharge and take on passengers at Brooklyn Bridge – City Hall, one station to the north.
South Ferry (see diagram) was a two-track subway loop station in New York City, with a sharply curved side platform for each track. Due to problems with train length and platform clearance, this station was replaced by a standard stub terminus with two tracks and an island platform (South Ferry), although the original trackage remains in use for turning trains. After the latter station was damaged in Hurricane Sandy, the former station was reopened temporarily to provide service to the ferry terminal until the repairs to the latter station are complete.^[1]
13th Street (formerly Juniper Street) is the eastern terminus for the SEPTA Subway-Surface Lines in Philadelphia, and trolleys turn on a balloon loop
69th Street is the western terminus for the Market Frankford Line in Philadelphia, and rapid transit trains use a double-track balloon loop for turning & staging.
Bowdoin Station on the MBTA Blue Line in Boston has a wedge-shaped island platform inside a balloon loop. The boarding platform is long enough for only four cars, but all of the trains on the line are six cars so only the rear four can be boarded at Bowdoin.
Mattapan Station on the MBTA Ashmont–Mattapan High Speed Line in Boston, has trolley cars unload passengers at the platform, then uses a balloon loop to return to the same platform to load inbound passengers.
World Trade Center station on the PATH subway system linking New York and New Jersey.
Grand Central Terminal, New York City - stacked upper and lower level loops (lower loop has since been removed)
Union Pacific Railroad at Truckee, California - loop to avoid needing to reverse rotary snow plows^[2]
Newark City Subway at Penn Station and Hudson Bergen Light Rail at North Bergen in New Jersey
Paulsboro Marine Terminal, planned loop for dockside access^[3]
The two terminal stations of North Hollywood Station and Chatsworth Station for the Orange Line Metro Bus Transit of Los Angeles, California have their platforms on a balloon loop.

United Kingdom

Dungeness, Romney, Hythe and Dymchurch Railway, Kent, England: single track, single platform for both boarding and alighting.^[4]
Merseyrail, the wirral line underground loop under Liverpool, England (3 stations on loop)
Ruislip Lido Railway, a miniature railway in West London, England
The Eurotunnel Shuttle uses balloon loops: since the two tracks cross over at the French end the whole line forms a figure 8 loop. This evens the wear on the train wheels.
Central station in Newcastle upon Tyne is on a loop, allowing trains from the South to arrive via the King Edward VII Bridge and return using the High Level Bridge.
Peasholm on the North Bay Railway in Scarborough, North Yorkshire has a reverse balloon loop, with the "neck" of the balloon facing the buffer stop. The loop is used to allow the locomotive to run round the train and reverse at the same time.
The first Wembley Stadium station in London (opened 1923, closed 1968) was on a balloon loop, but the present station of that name is not.
Barmouth Ferry station on the Fairbourne Railway.
Blackpool Tramway has a balloon loop at each end of the system (Starr Gate and Fleetwood) and at two intermediate points.
The Charing Cross, Euston and Hampstead Railway (now Northern line) used a one-track balloon loop beneath the Thames to serve its southern terminus of Embankment tube station, When the line was extended the loop was sealed off.
The Piccadilly line has a one-track balloon loop (T4 loop) under Heathrow airport connecting in order Hatton Cross tube station , Heathrow Terminal 4 tube station, Heathrow Terminals 1, 2, 3 tube station and back to Hatton cross tube station.

Other

Various stations of the Hong Kong Tramways and MTR Light Rail
File:Stadtbahn Charleroi, Gleisplan 1997.png
The Charleroi Pre-metro system features two balloon loops, at Beaux-Arts and Waterloo stations.

In the Charleroi Pre-metro, both the Beaux-Arts and Waterloo stations have balloon loops. At Beaux-arts, trains between Sud and Anderlues (line 89, both directions) first run through the station on a platformless track, take the underground balloon loop then stop at the platform leading to their destination. Waterloo station services three lines (54, 55 and 88) going to three directions, on a single island platform. Trains from Gilly station either diverge to the right and end up at the station to continue to Parc station, or diverge to the left to end up on the other end of the island platform to go towards Beaux-Arts. At the station is also a bypass so trains can run from Gilly directly to Beaux-Arts, without halting at the platform. No scheduled trains thus fully run the loop (or the bypass).
The Amsterdam, Rotterdam and The Hague tram systems have balloon loops at the end of all lines. Only Amsterdam line 5 terminus at Amstelveen Binnenhof^[5] and The Hague lines branded as Randstadrail do not have balloon loops.
Across these city's there are several unused balloon loops that were in use until lines were extended or abolished. These loops however are still maintained for eventual purposes.
The municipality of The Hague however plans on removing them and purchase new trams with a drivers cabine on both sides of the tram.

Multiple stations on a balloon loop:

Heathrow Terminal 4 and Terminals 1,2,3 stations on the Piccadilly line of London Underground.^[6]
The LACMTA Blue Line has four stations on its loop through downtown Long Beach (California).
In Liverpool, England, on the Wirral Line of the Merseyrail network, trains arriving at Liverpool through the Mersey Tunnel fork left at Mann Island Junction onto a balloon loop, before reaching James Street (platform 1); they then call at deep-level platforms at Moorfields, Liverpool Lime Street and Liverpool Central before reaching James Street again (platform 3), then rejoin the original route at Mann Island Junction and then pass back through the Mersey tunnel.^[7]
The City Loop or Melbourne Underground Rail Loop, Melbourne, Australia, has five stations. There a four loops, one from the north east and three from the south west, on two levels. The loops are bi-directional. A connection enables one of the south east loops to be used as a circle line. The are no connections between the four loops.
In the Helsinki area, the Kehärata or Ring Rail Line is being built between an existing branch at Vantaankoski and the main line at Tikkurila, primarily to serve the airport which is presently only accessible by road. It is expected to open in 2014. Two existing stopping services (to Tikkurila and Vantaankoski) will be replaced by a single service which traverses the whole loop and returns to Helsinki, stopping twice on opposite sides of Pasila station. Four new stations are planned, but the loop will have a total of 21 stations, not counting Pasila or Helsinki. Roughly half of these stations are on the northbound and westbound mainlines, the loop line leaving them via diving junctions at Hiekkaharju and Huopalahti.
Rapid MetroRail Gurgaon in India.

With balloon loop: The balloon loop is past the station.

Brooklyn Bridge and City Hall stations in New York City.

Bad Herrenalb, Albtalbahn, Germany: the train passes the loop before arrival
Bowling Green on New York City's IRT Lexington Avenue subway line is the southern terminus for 5 service in the evenings & on weekends, with the South Ferry inner loop (see previous section) used to turn trains.
Brooklyn Bridge – City Hall, also on New York City's IRT Lexington Avenue Line, is the southern terminus for Lexington Avenue local service (the 6 <6> trains), with the City Hall loop (see previous section) used to turn trains.
Howard Station on the CTA Red Line in Chicago uses a balloon loop to turn a northbound train back south. Because the other end of the line does not contain a loop, the wear on the wheels is evened out after two trips.
The Irish Steam Preservation Society's line at Stradbally, Co.Laois, Ireland consists of a balloon loop: trains operate from the station and back again via the loop.
69th Street Terminal, the western terminus of the SEPTA Market-Frankford Line in Philadelphia: westbound trains discharge passengers at the platform and go around the loop to one of two eastbound platforms to pick up passengers.
Gateway Center in Pittsburgh formerly was the north/west end of the Pittsburgh Light Rail line. Westbound trains would discharge passengers at the inbound platform, then go around a loop to the outbound platform to pick up passengers. When the subway was extended in 2009-2012, the loop was removed; while the original outbound platform under Liberty Ave was left intact, the inbound platform was demolished and moved.
Kennington tube station, on the London Underground's Northern line: trains from the Charing Cross branch can terminate at Kennington and then run around a loop to return north. Trains from the Bank branch cannot use this loop.
Schwabstraße station on the Stuttgart S-Bahn: the loop is south of the station and completely underground
Tonnelle Avenue (HBLR station): the loop is to the west of the station.

Paris Métro

Non-passenger loops: Porte Dauphine (line 2), Porte des Lilas (line 3bis), Porte de Clignancourt and Porte d'Orléans (line 4)
Passenger loops: Nation (line 2), Charles de Gaulle – Étoile and Nation (line 6), Pré Saint-Gervais (line 7bis)
The western end of line 10 is a long loop: trains arriving at Mirabeau from Gare d'Austerlitz used to enter a loop with the following stations, Église d'Auteuil, Auteuil, Porte d'Auteuil (official terminus), Michel-Ange – Molitor, Chardon Lagache and Mirabeau again, to continue eastwards.
There also are a few loops used for stabling trains, for example west of Invalides and north of Porte de la Villette.

Tram Systems

Balloon loops are used extensively on tramway systems with single-ended trams. Usually located at termini, the loop may be a single one-way track round a block. Single-ended trams have a cab at only one end and doors on one side, making them cheaper and having more space for passengers. On tram systems with double-ended trams balloon loops are not required but may still be used as they can provide greater turn-around capacity than a stub terminus; the Birmingham Corporation Tramways terminus at Rednal had a balloon loop in addition to the conventional stub tracks, providing extra capacity to handle weekend and bank holiday crowds visiting the nearby Lickey Hills. The Milan interurban tramway network, although using double-ended trams, had balloon loops at termini within the city limits so that they could be used as backup termini by the single directional trams used on urban service. In Milan, tramway depots are built as balloon loops, just as urban termini. Another example is in Potsdam, Germany.